核桃雄花中总多酚提取工艺的研究

采用单因素和正交试验研究核桃雄花中多酚类物质的最佳提取工艺条件。通过对4种不同溶剂(无水乙醇、甲醇、丙酮和乙酸乙酯)在相同试验条件下的浸提效果比较发现,甲醇是核桃雄花中总酚类物质的最佳提取试剂。然后分别采用常规水浴浸提法和超声波辅助浸提法对甲醇体分数、浸提温度、浸提时间和料液比等因素进行研究,在确定最佳单因素水平的基础上,再利用正交试验优化以甲醇为浸提剂的提取工艺条件,试验得出超声波辅助浸提法具有用时短、总多酚提取量高的优点,其最佳工艺条件为:料液比1∶30(g/m L)、甲醇溶液体积分数30%、温度70℃、浸提时间10 min。在此条件下,核桃雄花中的总多酚含量可达6.56%,明显高于其他条件下的。     

Hierarchical electromagnetic absorption in micro-waveguide stuffed with magnetic media for resin-based composites of graphene nanosheets and manganese oxides

Waveguide configurations of hierarchical system are proposed as new microstructures for composites in absorbing enhancement. Supercritical fluid (SCF) one-pot exfoliation of layered graphite and manganese oxide mixing materials is developed to obtain a hierarchical system, containing graphene nanosheets (GNS) and exfoliated manganese oxides (EMO) in different sizes. Composites with GNS–EMO embedded in epoxy resin matrix are produced for a design of dielectric and magnetic loss integrated absorber. Volume fraction of GNS–EMO in composites is given for an optimal quantity of resin epoxy in fixation and formation. The effect of mixing ratios between electric and magnetic components is provided for the design of dielectric and magnetic loss integrated absorbers. Frequency shifting phenomena are revealed in the component adjusting course. Excluding the offsetting sizes, reflection loss of composites is enhanced as thickness increases. Synergistic effect of electric and magnetic coordinated materials demonstrates the superiority of micro-waveguide structures in GNS–EMO composite absorber.     

Synthesis and electrochemical properties of layered Li[Ni0.333Co0.333Mn0.293Al0.04]O2−zFz cathode materials prepared by the sol–gel method

The cathode-active materials, layered Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z (0 ≤ z ≤ 0.1), were synthesized from a sol–gel precursor at 900 °C in air. The influence of Al–F co-substitution on the structural and electrochemical properties of the as-prepared samples was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and electrochemical experiments. The results showed that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z has a typical hexagonal structure with a single phase, the particle sizes of the samples tended to increase with increasing fluorine content. It has been found that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 showed an improved cathodic behavior and discharge capacity retention compared to the undoped samples in the voltage range of 3.0–4.3 V. The electrodes prepared from Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 delivered an initial discharge capacity of 158 mAh⁻¹ g and an initial coulombic efficiency is 91.3%, and the capacity retention at the 20th cycle was 94.9%. Though the F-doped samples had lower initial capacities, they showed better cycle performances compared with F-free samples. Therefore, this is a promising material for a lithium-ion battery.     

Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.     

无线传感器网络（WSN）在花卉大棚环境监测中的应用研究

针对传统花卉大棚环境参数监测系统的某些缺点,本文对基于Zigbee技术的无线传感器网络在花卉大棚中的应用可行性进行分析和研究,并建立了花卉大棚无线环境监测系统,使得该监测系统的各节点位置、监测范围、节点扩展性、节点间距离都得以改善和提高。     

嵌入式调试中的数据获取和错误定位

嵌入式软件系统因其软件相关性和硬件相关性而比常规软件的调试复杂很多,特别是在数据获取和故障定位方面最为突出。从嵌入式软件开发与常规软件开发的异同着手,以该行业实践积累为基础,列出并讨论了一些行之有效的数据获取及错误定位方法,希望能为该领域开发人员提供一点帮助。     

基于嵌入式技术的倾角传感器检测系统设计

介绍了加速度传感器MMA7260的工作原理、结构及功能,设计了一个基于ARM的实时嵌入式自动检测系统,使用μC/OS-II操作系统,构造一个具有角度测量、相关数据处理以及与上位机通信等功能的现场角度测量单元,上位机则主要完成系统监控和人机交互等功能。     

一类负模量Kirchhoff - Carrier方程的解

利用变分方法和反证法研究了一类含有非线性项的Kirchhoff - Carrier方程,证明了当0<λ1时,该方程至少存在一对非平凡解,且当λ≥a λ₁时该方程不存在同号解.     

Characterization of wet microalgal cells pretreated with steam for lipid extraction

Steam pretreatment was employed to disrupt microalgal cells for lipids extraction.Effects of steam pre-treatment on microstructure of microalgal cells were investigated through scanning electron microscopy(SEM) and transmission electron microscopy (TEM).Effect of treatment on lipid extraction was also stud-ied.Microalgal cell walls were distorted after steam pretreatment due to the hydrolysis of organic macro-molecules contained in cell wall.Maximum curvature was increased from 1.88 × 10-6 m-1 to 1.43 × 10-7 m-1 after treatment with the steam at 130 ℃.The fractal dimension of microalgal cells increased from 1.25 to 1.30 after pretreatment for 15 min,and further increased to 1.47 when the pre-treatment time was increased to 60 min.Increased steam pretreatment temperature and time enhanced the hydrolysis of organic macromolecules,and finally destroyed microalgal cell walls at pretreatment temperature of 130 ℃ and pretreatment time of 60 min.Lipid extracted from wet microalgal was signif-icantly increased (2.1-fold) after pretreatment.